Modding PSU Cover Corsair RM1000i part 2

Custom be quiet! Dark Power Pro 11 PSU cover / secondary floor part 2

Spread the love

The whole concept when I started thinking about my custom PSU cover or secondary floor, were to mount the top of the pump above the floor and hide the pump under. Adding to that effect I wanted the reservoir next to it.

When I did my initial drawing I didn’t have the pump measurements, but was very exciting to realize it was wider than I thought and had the same dimensions as the reservoir. It was time to cut the top floor and put my custom EKWB D5 pump and Aqualis XT 880 ml bracket to good use. With the extra length of the be quiet! Dark Power Pro 11 PSU I will need all the room I can get.

Modding PSU Cover Corsair RM1000i part 2

My original sketch that I used for planning and discussing the pros and cons of my mounting. It’s not an optimal pump / reservoir placement, but it will work and it will stay true to my mod and my design theme.

Modding PSU Cover Corsair RM1000i part 2

Started to take measurements of the height of the bracket. Had an idea of securing the bracket with the rubber grommets included with the case, but those extra 2mm was enough to push the bracket into the floor. Might need to cut of part of the EKWB pump bracket in final fitting.

 

Modding PSU Cover Corsair RM1000i part 2

Measuring center and left most placement I can go without pushing the Aqualis XT 880 ml reservoir into the case front fans. This looks just right. Placement of the custom EKWB D5 and Aqualis bracket pretty much sorted it self, due to the case holes below, but I had some room to push the top floor 8mm.

 

Modding PSU Cover Corsair RM1000i part 2

A previous trip to the hardware store had secured a new drill measuring 80mm, same as both the pump and the Aqualis XT 880 reservoir. Well, 78mm for the pump to be precise, but a little room is needed. I sacrificed a piece of 5mm acrylic to do a test drill to ensure it would work and with a few stops to clean the drill and let the acrylic cool was all it took. Fastened the custom floor, now ready, and went to work to cut my two holes.

 

Modding PSU Cover Corsair RM1000i part 2

So happy with the result. Looks just as I had envisioned it almost 2 months ago when I started planning this build in my head. The fit was perfect and my previously crafted bracket even more perfect. Just one more thing to ensure, would the Aqualis XT 880 reservoir fit?.

 

Modding PSU Cover Corsair RM1000i part 2

Like a glove 🙂 My top floor piece or PSU cover as I originally called it, was finally done. Still some work to do to glue the floor to the previously crafted custom PSU Cover front side that will eventually cover my be quiet! Dark Power Pro 11 850W PSU and EKWB D5 plexi pump.

 

Modding PSU Cover Corsair RM1000i part 2

The height of the top floor combined with the bracket is just perfect. Happy when measurements are correct and you get to see the result of an idea. I’m extremely happy at this point. Only one thing left to do and that is to combine this top part with the side part and then final finish. Will be a shame to hide the beautiful be quiet! Dark Power PSU, but hopefully I will make up for it with the overall design idea.

 

Modding PSU Cover Corsair RM1000i part 2

At this point I haven’t been able to secure real acrylic cement in Sweden. Superglue had to due and not worried as the piece isn’t going to be transparent, but it’s on my shopping list.

 

Modding PSU Cover Corsair RM1000i part 2

Glued and done! Now the shape of my floor is more visible. Made sure from start it would be as tight fit as possible. Also added two channels for cables and ventilation matching the case bottom motherboard bracket.

 

Modding PSU Cover Corsair RM1000i part 2

Made a cardboard / paper motherboard just to secure size, height and placement of the motherboard. Final finish and last mounting adjustments coming in next update…

Related Posts

3 Replies to “Custom be quiet! Dark Power Pro 11 PSU cover / secondary floor part 2”

  • Nathaniel Létourneau

    Hey, this might sorta late, but do you still plans/drawings of your psu shroud? I plan to make one myself and knowing yours worked out woud be just that much helpful.

    • Zeuligan Zork

      I never had any drawings, just made it of cardboard and copied that onto acrylic. I plan to make mine design available, just need to finish the build. Just let me know if there is anything specific I can help you with and I will try to do my best to help you out.

      • Nathaniel Létourneau

        I got the same case, so I was wondering if you had technical plans. Would’ve saved me the time of making one for myself. Still gonna do it 😛 thanks for the quick reply! 🙂

Leave a Reply

Your email address will not be published. Required fields are marked *